X1E
DiscontinuedBambu's enterprise and engineering flagship. The X1E took the X1 Carbon platform and added an actively heated 60°C chamber, a 320°C hardened-steel hotend, and a full enterprise networking stack: Ethernet, WPA2-Enterprise Wi-Fi, physical kill-switches and off-cloud LAN-only operation. Discontinued March 2026 as part of the X1 series wind-down. For a current active-chamber engineering printer, see the H2S, H2D or X2D.
Image: Bambu Lab.
Bambu ended the X1E (and the whole X1 series) on 31 March 2026. It is no longer sold new. For current active-chamber engineering printers, see the H2S ($1,199), H2D ($1,549) or X2D ($649).
Should I buy the X1E?
The X1E is discontinued. It was built for enterprise and engineering teams that needed an active chamber plus secure, off-cloud networking. If you specifically need those enterprise controls (Ethernet, WPA2-Enterprise, LAN-only operation), look for a used or clearance unit. For a new machine with an active heated chamber, the H2S ($1,199) and H2D ($1,549) are the current picks; the X2D ($649) is the direct X1-series successor with a 65°C active chamber for far less.
Who should buy the X1E?
- Buying newLook elsewhere
Bambu ended the X1 series, X1E included, on March 31, 2026; for an actively heated chamber the H2S is a current pick. H2S → (Bambu blog) - Locked-down networksDepends
Ethernet, WPA2-Enterprise Wi-Fi and a LAN-only mode that works without Bambu Cloud; today only as a used unit. P1S vs X1E → (Bambu X1E page) - Engineering materialsDepends
A 320°C hotend and a chamber actively heated to 60°C; the H2S goes to 350°C and 65°C. H2S → (Bambu X1E page)
Known issues
- Discontinued March 31, 2026: Bambu promises firmware bug fixes and feature updates until May 31, 2027, security patches until May 31, 2029 and spare parts until March 31, 2031. (Bambu blog)
- Offline updates from 01.01.02.00 or older need the 01.01.50.02 helper firmware before 01.02.00.00 or later; online updates are not affected. (Bambu release notes)
Known issues only from Bambu's own wiki, firmware release notes, FAQ, blog and recall pages, checked October 2, 2026. Specs: our table below and Bambu's spec pages.
| Motion & Print | |
|---|---|
| Build volume | 256 × 256 × 256 mm (10.1 × 10.1 × 10.1 in) |
| Max speed | 500 mm/s |
| Acceleration | 20,000 mm/s² |
| Motion system | CoreXY |
| Layer height (0.4 mm nozzle) | 0.08–0.28 mm (Bambu Studio default range) |
| Extruder | Direct drive |
| Nozzle (stock) | 0.4 mm hardened steel |
| Temperature & Enclosure | |
|---|---|
| Nozzle max | 320°C |
| Bed max | 110°C at 220V, 120°C at 110V |
| Enclosure | Yes |
| Chamber heating | Active (60°C) |
| HEPA filter | Yes |
| Carbon filter | Yes |
| Bed surface | Textured PEI (magnetic) |
| Lidar sensor | Yes |
| AI failure detection | Yes (Vision + spaghetti detection) |
| Auto leveling | Yes (Lidar-assisted) |
| Vibration comp. | Yes (accelerometer) |
| Flow calibration | Yes (Lidar) |
| Camera | Yes (included) |
| AMS | AMS, AMS 2 Pro or AMS HT (up to 4 units and 16 colors; AMS 2 Pro and AMS HT since firmware 01.02.00.00) |
| Connectivity | Wi-Fi, Ethernet (RJ45), WPA2-Enterprise |
| Security | Physical kill-switches, off-cloud / LAN-only mode |
| Weight | 16 kg |
| Power supply | 100–240V AC |
| Status | Discontinued (March 2026) |
The X1E was Bambu's answer to enterprise and engineering buyers who liked the X1 Carbon but needed more: an actively heated 60°C chamber for demanding materials, a 320°C hardened-steel hotend, and a security and networking stack aimed at IT departments: Ethernet, WPA2-Enterprise Wi-Fi, physical kill-switches, and the ability to run fully off-cloud on a local network. At its $2,499 launch price (2023; Bambu US now lists $2,899 incl. AMS) it was priced for organizations, not hobbyists.
Its real differentiators were the active chamber and the enterprise controls. The 60°C heated chamber made ABS, ASA and higher-temperature engineering filaments far more reliable than the passive X1 Carbon, while LAN-only operation and kill-switches addressed data-security requirements that ruled out cloud-connected printers in some environments.
Now that it is discontinued, its role is filled by the H-series. The H2S ($1,199) and H2D ($1,549) both offer an active 65°C chamber, higher 350°C temps and larger build volumes, and the X2D ($649) is the direct X1-series successor with a 65°C active chamber. Buy a used or clearance X1E only if you specifically need its off-cloud enterprise networking package.
Pros
- Active 60°C heated chamber: reliable ABS/ASA and engineering filaments
- 320°C hardened-steel hotend for higher-temp materials
- Lidar first-layer calibration and flow sensing
- AI Vision + spaghetti/failure detection
- Enterprise networking: Ethernet (RJ45), WPA2-Enterprise Wi-Fi
- Off-cloud / LAN-only operation with physical kill-switches
- Fully sealed enclosure with 3-stage filtration: G3 pre-filter, H12 HEPA, activated carbon
- AMS up to 16 colors
Cons
- Discontinued March 2026. No longer sold new
- $2,499 at launch in 2023 (Bambu's page now lists a $2,899 MSRP with AMS): enterprise pricing, hard to justify for hobby use
- H2S ($1,199) and H2D ($1,549) now offer active chambers for less
- X2D ($649) is the direct successor at a fraction of the price
- 256 mm build volume, same as much cheaper printers
- Single nozzle: no dual-material or IDEX printing
The X1E was Bambu's first printer built specifically for corporate IT environments; today the H2D Pro (resellers only) offers Ethernet, WPA2-Enterprise/802.1X and a removable network module, though its kill switch covers Wi-Fi only. Its enterprise package covered the requirements that keep cloud-connected consumer printers out of secure networks:
| Feature | What it does |
|---|---|
| Ethernet (RJ45) | Wired network connection for reliability and managed networks. |
| WPA2-Enterprise Wi-Fi | Connects to corporate/campus 802.1X networks, not just home WPA2-PSK. |
| Off-cloud / LAN-only mode | Full operation without any cloud connection, for air-gapped or restricted networks. |
| Physical kill-switches | Hardware toggles to cut connectivity, for data-sensitive environments. |
| Material | Support | Notes |
|---|---|---|
| PLA / PLA+ | Excellent | Lidar calibration makes already good PLA prints even better. |
| PETG | Excellent | Lidar catches any first-layer adhesion issues early. |
| ABS / ASA | Excellent | Active 60°C chamber makes these first-class, better than the passive X1 Carbon. |
| TPU (flexible) | Supported | Direct drive handles flexible filament well. |
| Nylon / PA | Good | Active chamber and 320°C hotend handle many PA grades. Dry filament essential. |
| CF / GF composites | Hardened nozzle | Hardened-steel nozzle stock. Active chamber helps layer adhesion on CF-PA. |
| PC | Good | Bambu rates PC superior on the X1E: 320°C hotend plus active chamber. |
| PA-CF / PPA-CF / PPS-CF | Good | Bambu rates fiber-filled PA superior and PPA-CF/GF, PPS and PPS-CF/GF ideal on the X1E (320°C hotend, active chamber). |
Active chamber for ABS/ASA: Let the chamber reach 60°C before starting. Unlike passive enclosures, the X1E actively heats, so warping risk drops significantly on large engineering parts. Set the bed to 100°C for ABS.
Lidar calibration: Let the full first-layer Lidar scan run on every print. It adds a couple of minutes but catches bed offset issues before you waste filament.
LAN-only / off-cloud mode: Enable LAN Only in Settings to run without any cloud connection. Combined with Ethernet and the kill-switches, this keeps the X1E inside a restricted network. Connect Orca Slicer via local IP and access code.
WPA2-Enterprise: For 802.1X corporate networks, enter the enterprise credentials in the network setup rather than a plain Wi-Fi password. Wired Ethernet is the more reliable option in managed environments.
What replaced the X1E? There is no one-for-one replacement. For an active heated chamber, the H2S ($1,199) and H2D ($1,549) are the current engineering picks, and the X2D ($649) is the direct X1-series successor with a 65°C active chamber. None fully replicate the X1E's off-cloud enterprise networking package.
X1E or X1 Carbon? Both are discontinued. The X1E added an active 60°C chamber, a 320°C hotend and enterprise networking over the passive X1 Carbon. If you need those, the X1E was the one to have; otherwise the cheaper X1C covered the same core platform.
Why was it so expensive? The $2,499 launch price (Bambu's page now lists $2,899 MSRP with AMS included) reflected the enterprise positioning: active chamber, 320°C hardened hotend, and the networking/security stack aimed at corporate IT. It was priced for organizations, not hobbyists.
Can I still run it off-cloud? Yes. The X1E's LAN-only operation, Ethernet, WPA2-Enterprise and physical kill-switches still work on existing units. That off-cloud capability is the main reason to seek out a used or clearance X1E today.